Greg Kroah-Hartman
598cf27219
Link: https://lore.kernel.org/r/20260217200002.683975158@linuxfoundation.org Tested-by: Florian Fainelli <florian.fainelli@broadcom.com> Tested-by: Takeshi Ogasawara <takeshi.ogasawara@futuring-girl.com> Tested-by: Peter Schneider <pschneider1968@googlemail.com> Tested-by: Jon Hunter <jonathanh@nvidia.com> Tested-by: Salvatore Bonaccorso <carnil@debian.org> Tested-by: Brett A C Sheffield <bacs@librecast.net> Tested-by: Mark Brown <broonie@kernel.org> Tested-by: Luna Jernberg <droidbittin@gmail.com> Tested-by: Ronald Warsow <rwarsow@gmx.de> Tested-by: Justin M. Forbes <jforbes@fedoraproject.org> Tested-by: Ron Economos <re@w6rz.net> Tested-by: Miguel Ojeda <ojeda@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
51 lines
1.6 KiB
Plaintext
51 lines
1.6 KiB
Plaintext
* Wiznet w5x00
|
|
|
|
This is a standalone 10/100 MBit Ethernet controller with SPI interface.
|
|
|
|
For each device connected to a SPI bus, define a child node within
|
|
the SPI master node.
|
|
|
|
Required properties:
|
|
- compatible: Should be one of the following strings:
|
|
"wiznet,w5100"
|
|
"wiznet,w5200"
|
|
"wiznet,w5500"
|
|
- reg: Specify the SPI chip select the chip is wired to.
|
|
- interrupts: Specify the interrupt index within the interrupt controller (referred
|
|
to above in interrupt-parent) and interrupt type. w5x00 natively
|
|
generates falling edge interrupts, however, additional board logic
|
|
might invert the signal.
|
|
- pinctrl-names: List of assigned state names, see pinctrl binding documentation.
|
|
- pinctrl-0: List of phandles to configure the GPIO pin used as interrupt line,
|
|
see also generic and your platform specific pinctrl binding
|
|
documentation.
|
|
|
|
Optional properties:
|
|
- spi-max-frequency: Maximum frequency of the SPI bus when accessing the w5500.
|
|
According to the w5500 datasheet, the chip allows a maximum of 80 MHz, however,
|
|
board designs may need to limit this value.
|
|
- local-mac-address: See ethernet.txt in the same directory.
|
|
|
|
|
|
Example (for Raspberry Pi with pin control stuff for GPIO irq):
|
|
|
|
&spi {
|
|
ethernet@0: w5500@0 {
|
|
compatible = "wiznet,w5500";
|
|
reg = <0>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <ð1_pins>;
|
|
interrupt-parent = <&gpio>;
|
|
interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
|
|
spi-max-frequency = <30000000>;
|
|
};
|
|
};
|
|
|
|
&gpio {
|
|
eth1_pins: eth1_pins {
|
|
brcm,pins = <25>;
|
|
brcm,function = <0>; /* in */
|
|
brcm,pull = <0>; /* none */
|
|
};
|
|
};
|