Greg Kroah-Hartman
598cf27219
Link: https://lore.kernel.org/r/20260217200002.683975158@linuxfoundation.org Tested-by: Florian Fainelli <florian.fainelli@broadcom.com> Tested-by: Takeshi Ogasawara <takeshi.ogasawara@futuring-girl.com> Tested-by: Peter Schneider <pschneider1968@googlemail.com> Tested-by: Jon Hunter <jonathanh@nvidia.com> Tested-by: Salvatore Bonaccorso <carnil@debian.org> Tested-by: Brett A C Sheffield <bacs@librecast.net> Tested-by: Mark Brown <broonie@kernel.org> Tested-by: Luna Jernberg <droidbittin@gmail.com> Tested-by: Ronald Warsow <rwarsow@gmx.de> Tested-by: Justin M. Forbes <jforbes@fedoraproject.org> Tested-by: Ron Economos <re@w6rz.net> Tested-by: Miguel Ojeda <ojeda@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
48 lines
1.6 KiB
C
48 lines
1.6 KiB
C
/* SPDX-License-Identifier: GPL-2.0 */
|
|
/*
|
|
* board initialization code should put one of these into dev->platform_data
|
|
* and place the isp1362 onto platform_bus.
|
|
*/
|
|
|
|
#ifndef __LINUX_USB_ISP1362_H__
|
|
#define __LINUX_USB_ISP1362_H__
|
|
|
|
struct isp1362_platform_data {
|
|
/* Enable internal pulldown resistors on downstream ports */
|
|
unsigned sel15Kres:1;
|
|
/* Clock cannot be stopped */
|
|
unsigned clknotstop:1;
|
|
/* On-chip overcurrent protection */
|
|
unsigned oc_enable:1;
|
|
/* INT output polarity */
|
|
unsigned int_act_high:1;
|
|
/* INT edge or level triggered */
|
|
unsigned int_edge_triggered:1;
|
|
/* DREQ output polarity */
|
|
unsigned dreq_act_high:1;
|
|
/* DACK input polarity */
|
|
unsigned dack_act_high:1;
|
|
/* chip can be resumed via H_WAKEUP pin */
|
|
unsigned remote_wakeup_connected:1;
|
|
/* Switch or not to switch (keep always powered) */
|
|
unsigned no_power_switching:1;
|
|
/* Ganged port power switching (0) or individual port power switching (1) */
|
|
unsigned power_switching_mode:1;
|
|
/* Given port_power, msec/2 after power on till power good */
|
|
u8 potpg;
|
|
/* Hardware reset set/clear */
|
|
void (*reset) (struct device *dev, int set);
|
|
/* Clock start/stop */
|
|
void (*clock) (struct device *dev, int start);
|
|
/* Inter-io delay (ns). The chip is picky about access timings; it
|
|
* expects at least:
|
|
* 110ns delay between consecutive accesses to DATA_REG,
|
|
* 300ns delay between access to ADDR_REG and DATA_REG (registers)
|
|
* 462ns delay between access to ADDR_REG and DATA_REG (buffer memory)
|
|
* WE MUST NOT be activated during these intervals (even without CS!)
|
|
*/
|
|
void (*delay) (struct device *dev, unsigned int delay);
|
|
};
|
|
|
|
#endif
|